Showing results: 16 - 30 of 2632 items found.
-
Iris Power LP
Shaft monitoring to indicate high voltage and current on the motor or generator from poor shaft grounding performance prior to bearing failures.
-
Shanghai Jiuzhi Electric Co., Ltd.
AC voltage and current test system is used to be the electrical test performed on a component (such as, bushings, arrestors, insulating materials) or high voltage products (such as, high voltage cables, power transformers, instrument transformers, gas insulated switchgears, air insulated switchgears, high voltage insulators and etc) to determine the effectiveness of its insulation. For the safety of high voltage transmission , testing insulation integrity is essential for all high voltage products.
-
T5-1000 -
Fluke Corporation
Measure current up to 100 A without breaking the circuit with OpenJaw™ design. The T5-1000 Electrical Tester is a versatile troubleshooting tool to carry to every job site. Use it to check voltage, continuity, and current–all with one compact tool.
-
GPTN -
Holding Informtest
The module is intended for use as part of information measuring systems based on the VXI-bus trunk. The module is designed to generate constant current or constant voltage.
-
CDY Series -
Shanghai Jiuzhi Electric Co., Ltd.
Impulse voltage generator can be used to generate impulse voltage simulating lightning strokes and switching surges, it also can be used to generate chopping wave, oscillating wave, steeping wave and 4/10us, 8/20us, 10/350us impulse current wave, if property add some extra equipments.
-
Synectic Electronics
The SY018 DIN rail Voltage to 4-20mA signal converter is used to communicate analogue signals over long distances where electrical interference may be a problem. This solution is often used in the process control industry to collect the analogue values from a wide array of remote sensors. The converter is valuable because current signals are much less susceptible to noise than voltage signals. A voltage signal can be converted to current and broadcast over a long distance. 4-20 mA transmitters are common in the industry and used with high-quality sensors. The resulting signals can be use in controlling drives or to trigger instruments that have settable thresholds and limits.
-
Shanghai Jiuzhi Electric Co., Ltd.
Our advanced CDY series Impulse test systems are used for impulse voltage testing of transformers, cables, gas-insulated switchgears (GIS), arresters, and other high-voltage devices. The test systems generate lightning impulse voltage (LI, 1.2/50 µs), chopping lightning impulse voltages (LIC, front time 1.2 µs, front, crest or tail chopped), and switching impulse voltage (SI, 250/2500 µs) in accordance with IEC 60060-1; as well as IEC 60076-3 for transformers, and IEC 62067, 60840 and 60502-1 for cables). By adding extra components, our impulse test system also can generate steeping wave (SWI, >2500kV/ µs) and impulse current (IC, 4/10 µs, 8/20µs, 10/350µs).
-
MC140i -
Powertek LLC
Multifunction calibrator MC140i is ideal for calibration of voltmeters, ammeters, DMMs and panel meters. AC/DC voltage 1uV to 1000V. Current 50uA? to 1000A using test coil. Deviation control along readout. 0.0035% basic dc accuracy. 0.03% basic ac accuracy. Supplied with RS232 interfaces. UKAS/NIST Traceable
-
FLIR VT8-Series -
Teledyne FLIR
The FLIR VT8-Series are high-quality voltage, continuity, and current testers. They feature an optimized, open-jaw design that can fit into tight spaces and reliably measure large-diameter cables. The VT8-600 carries a CAT III-600 V/CAT IV-300 V safety rating and a 100 A/600 V measuring range, while the VT8-1000 carries a CAT III-1000 V/CAT IV-600 V safety rating and a 200 A/1000 V measuring range. Extensive measurement features make the VT8-Series versatile tools – just one meter can get the job done.
-
Educated Design & Development, Inc.
For measuring current, especially higher currents and quicker than series ammeters. These units are considered the finest available. All units are extremely rugged, reliable, and versatile.
-
Time Electronics
Each model in our portable test equipment range is designed for accuracy and reliability, providing high performance and ease of use for applications. Products are used in various lab and field applications across industries such as research and development, semiconductor, and process control. For higher range electrical source and measure we have a series of bench multifunction calibrators and multimeters.
-
Shanghai Jiuzhi Electric Co., Ltd.
SGV Series DC test systems are used to test components and complete systems found in electrical power supply system what operate on DC voltage. Samgor DC voltage test systems can be implemented for tests with highest voltages according to IEC 60060-1.
-
P02-802 -
The Eastern Specialty Company
The TESCO High Voltage Non-Contact Current Probe (Catalog No. P02-802) was developed using current sensor technology. It is a two-piece, True RMS ammeter with a fiber optic link between the high voltage sensor and the readout at ground potential. The sensor is mounted on a hotstick and slipped over a high voltage line.
-
Monarch Instrument
The Track-It™ DC Voltage and Current Data Loggers are two channel battery powered stand alone compact data loggers that record up to 32,000 samples each of DC Voltage or Current data. Units are available in 4 DC voltage ranges or for DC current. Simply plug the data logger into an available USB port on your PC and customize the settings or transfer data with the included Track-It Software program.
-